4-in-1 Bucket forks for loaders from CTI

1-800-423-8689 303-371-8097 Since 1967	CTI 4-in-1 Bucket Forks	Manufacturer of quality attachments for your equipment

CTI Products

CTI Information

Advice | Model Specifications

Recognizing that "4-in-1" buckets have the unique ability to grab and hold many things, including attachments, CTI has designed a revolutionary type of fork that takes advantage of that feature - its new 4-in-1 Bucket Forks.
The features of these new forks, on which a patent is pending, include:

No welding, no screws, no holes in the bucket. The closed clam holds the forks firmly in place.
Rigid mounts - the forks don't swing or shift sideways.
Easy to operate - the forks are level when the cutting edge is level.
Easy on, easy off - No lifting, just pick them up and set them down with the machine.
Towers that are 37 inches tall to keep loads in place and allow the operator to see the forks from the cab.
Round grab bars on the towers to make it easy to move the forks on the ground or on and off a truck.
Safety chains to ensure the forks will stay in place even if the bucket is accidentally opened.
Attaches to the most reinforced part of the bucket - the cutting edges.

To mount CTI's new 4-in-1 bucket forks, just open the bucket "clam", drive into the forks, pick them up with the front cutting edge, and close the clam on the retainer bars that fit between the two back cutting edges. Then hook up the safety chains and go to work!

When you've finished moving your loads, set the forks down, unhook the chains, open the clam, back out of the forks, and go.

CTI's 4-in-1 bucket forks are available with a 6000 lb. lift capacity and 48" solid steel tines for Caterpillar, Case, John Deere, Gannon for John Deere, and Komatsu 4-in-1 buckets. (An 8000 lb model with 60 inch tines is available by special order).

Features | Advice | Model Specifications | Top

Press Release

CTI ADVICE ON 4-IN-1 BUCKET FORKS

Buckets with clam cylinders that have a tendency to bleed off should be equipped with an accessory check valve before installing CTI 4-in-1 Bucket Forks.
These forks can be removed from a truck or trailer and repositioned on the ground using the round grab bars at the top of the towers. Use the bucket clam to grasp the top of the towers under the round grab bars so the forks do not slip through the clam. Do not use the safety chain and hook for lifting or moving the forks.
Remember that lifting capacity is limited by both the tine capacity of the forks and the capacity of the loader, whichever is less. Also, because of the increased load radius with the forks and their additional weight, loader lift capacity is reduced by approximately 17% when forks are added.

Click this icon for general sensible usage and safety tips.

Features | Advice | Model Specifications | Top

4-IN-1 BUCKET FORK SPECIFICATIONS

CTI 4-in-1 Bucket Fork Attachments now come in two lift capacities. Using the connected model list can help you in finding the right fork size for your equipment.

CTI Model	Machines	Bucket Part Number	Bucket Size	CTI Part Number	CTI Retainer Bars	Measurement "B" *
MP60	Caterpillar	1120938	1.25 cu yd	460-0700	460-0015	23.50 inches
MP60	Komatsu	312630087	1.36 cu yd	460-0700	460-0015	21.25 inches
MP60	John Deere, including "Gannon for John Deere"	AT150456 AT186432 AT177940	1.37 cu yd 1.32 cu yd 1.00 cu yd	460-0701	460-0020	21.00 inches 21.75 inches 20.50 inches
MP60	Case	376288A2	1.30 cu yd	460-0702	460-0035	19.50 inches
* Measurement "B" is the distance from the front cutting edge to the scraper cutting edge across the bottom of the bucket.

CTI Model	Fits Bucket Measurement "B" *	Lift Capacity at 24" Load Center	Tine Length	Tower Height	Tine Size	Weight
MP60	19.5 - 23.5 inches	6000 lbs.	48 inches	37 inches	2 x 4 inches	512 lbs.
**MP80	19.5 - 23.5 inches	8000 lbs.	60 inches	37 inches	2 x 5 inches	752 lbs.
** Model MP80 is Available by Special Order Only for all of the above machines. For more information, contact factory at 1-800-423-8689.

Features | Advice | Model Specifications | Top

Email:
sales@ctiattachments.com

Toll Free:
1-800-423-8689

Web Address:
www.ctiattachments.com

5070 Oakland St.
Denver, CO
80239

303-371-8097

4-in-1 Bucket Forks
Skid Steer Forks | Drive-In Forks | Clamp-on Forks | Asphalt Cutters
Equipment Match | How to Buy | Contact Us | About Us
Industry Info | CTI Search | CTI Home Page
Top

Web Design
by
Inventive
I

1-800-423-8689 303-371-8097 Since 1967

CTI 4-in-1 Bucket Forks

CTI Products

CTI Information

Advice | Model Specifications

Recognizing that "4-in-1" buckets have the unique ability to grab and hold many things, including attachments, CTI has designed a revolutionary type of fork that takes advantage of that feature - its new 4-in-1 Bucket Forks. The features of these new forks, on which a patent is pending, include:

No welding, no screws, no holes in the bucket. The closed clam holds the forks firmly in place.

Rigid mounts - the forks don't swing or shift sideways.

Easy to operate - the forks are level when the cutting edge is level.

Easy on, easy off - No lifting, just pick them up and set them down with the machine.

Towers that are 37 inches tall to keep loads in place and allow the operator to see the forks from the cab.

Round grab bars on the towers to make it easy to move the forks on the ground or on and off a truck.

Safety chains to ensure the forks will stay in place even if the bucket is accidentally opened.

Attaches to the most reinforced part of the bucket - the cutting edges.

To mount CTI's new 4-in-1 bucket forks, just open the bucket "clam", drive into the forks, pick them up with the front cutting edge, and close the clam on the retainer bars that fit between the two back cutting edges. Then hook up the safety chains and go to work!

When you've finished moving your loads, set the forks down, unhook the chains, open the clam, back out of the forks, and go.

CTI's 4-in-1 bucket forks are available with a 6000 lb. lift capacity and 48" solid steel tines for Caterpillar, Case, John Deere, Gannon for John Deere, and Komatsu 4-in-1 buckets. (An 8000 lb model with 60 inch tines is available by special order).

Features | Advice | Model Specifications | Top

CTI ADVICE ON 4-IN-1 BUCKET FORKS

Buckets with clam cylinders that have a tendency to bleed off should be equipped with an accessory check valve before installing CTI 4-in-1 Bucket Forks.

Remember that lifting capacity is limited by both the tine capacity of the forks and the capacity of the loader, whichever is less. Also, because of the increased load radius with the forks and their additional weight, loader lift capacity is reduced by approximately 17% when forks are added.

Click this icon for general sensible usage and safety tips.

Features | Advice | Model Specifications | Top

4-IN-1 BUCKET FORK SPECIFICATIONS

CTI 4-in-1 Bucket Fork Attachments now come in two lift capacities. Using the connected model list can help you in finding the right fork size for your equipment.

Features | Advice | Model Specifications | Top

4-in-1 Bucket Forks Skid Steer Forks | Drive-In Forks | Clamp-on Forks | Asphalt Cutters Equipment Match | How to Buy | Contact Us | About Us Industry Info | CTI Search | CTI Home Page Top

1-800-423-8689
303-371-8097
Since 1967

Recognizing that "4-in-1" buckets have the unique ability to grab and hold many things, including attachments, CTI has designed a revolutionary type of fork that takes advantage of that feature - its new 4-in-1 Bucket Forks.
The features of these new forks, on which a patent is pending, include:

4-in-1 Bucket Forks
Skid Steer Forks | Drive-In Forks | Clamp-on Forks | Asphalt Cutters
Equipment Match | How to Buy | Contact Us | About Us
Industry Info | CTI Search | CTI Home Page
Top